AGILE ALLY PLUS 6287 Manual de usuario Pagina 135
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Page 11-96287 ULTRA COMPATIBILITY
37 — Reserved
This option is reserved in the current ULTRA firmware, and it has no
equivalent in the ALLY PLUS.
38 — Reserved
This option is reserved in the current ULTRA firmware, and it has no
equivalent in the ALLY PLUS.
39 — Non-Transparency Trigger 1 Output
This command has no effect in the ALLY PLUS.
40 — Alternate Host Lockout Duration
The setting of this option will determine the settings of all four potential
alternate host ports on the ALLY PLUS (Options 80, 81, 82 and 83). The
ULTRA decimal value is executed as though it were the equivalent ALLY
PLUS hexadecimal value. The General Configuration Report will display
the hexadecimal value.
41 — Serial Alternate Host CTS Enabled
The setting of this option will affect the settings of both ALLY PLUS
Options 45 and 4B. A value of Y is executed as though it were an ALLY
PLUS value of 02, and a value of N is executed as an ALLY PLUS value
of 01. The General Configuration Report will display either 1=XON/
XOFF or 2=RTS/CTS.
42 — Reserved
This option is reserved in the current ULTRA firmware, and it has no
equivalent in the ALLY PLUS.
43 — Reserved
This option is reserved in the current ULTRA firmware, and it has no
equivalent in the ALLY PLUS.
44 — Reserved
This option is reserved in the current ULTRA firmware, and it has no
equivalent in the ALLY PLUS.
- 6287 ALLY PLUS 1
- Copyright Information 2
- Release Notes 2
- About AGILE 3
- Also From AGILE 4
- TABLE OF CONTENTS 5
- PROGRAMMABLE FUNCTION STRINGS 8
- TRANSLATE TABLES 10
- COAX HOST CONSIDERATIONS 10
- XEROX APPLICATIONS 11
- SCS DATA STREAMS 11
- DSC DATA STREAMS 11
- ALTERNATE HOST CONSIDERATIONS 12
- 6287 ULTRA COMPATIBILITY 12
- APPENDIX 14
- GLOSSARY 14
- About This Manual 15
- AGILE Product Warranty 16
- Page xviiPREFACE 17
- FCC Statement 18
- Warnings 19
- Electrical Shock 19
- Standard Factory Setup 19
- Serial Port Setup 19
- Coax Host Considerations 20
- Power-On Reset 20
- INTRODUCTION 21
- INSTALLATION 25
- Unpacking 26
- Connections 27
- Dual Printer Installation 29
- 6287 ALLY PLUS Front Panel 31
- Extended Modes 33
- Resetting to Defaults 34
- 6287 ALLY PLUS Power Up 34
- Connection Tests 35
- Coax Host Verification 36
- Alternate Host Verification 37
- Software Upgrades 39
- CONFIGURATION 41
- Configuration Defaults 43
- Configuration Groups 45
- Printer Output (Group #00) 45
- 01 — Output type 46
- 02 — Character set 46
- 03 — Plotter support 47
- 05 — Plotter support 47
- 11 — SCS left margin 48
- 12 — SCS right margin 48
- 13 — SCS top margin 49
- 14 — SCS bottom margin 49
- 15 — SCS line spacing 50
- 21 — DSC left margin 51
- 22 — DSC right margin 51
- 23 — DSC top margin 52
- 24 — DSC bottom margin 52
- 25 — DSC line spacing 53
- 30 — FF before Local Copy 55
- 31 — FF after Local Copy 55
- Serial Port Setup (Group #40) 56
- 44 (4A) — Stop bits 57
- Host Parameters (Group #50) 58
- 53 — Coax port timer 59
- 54 — LU1 bracketing 59
- SCS TH and RH -> 60
- 2C 00 06 01 00 0C 00 90 80 60
- 62 — Pseudo transparency 62
- 63 — DSC PTM trigger 1 64
- 64 — DSC PTM trigger 2 64
- 65 — SCS PTM trigger 1 64
- 66 — SCS PTM trigger 2 65
- 70 — DisplayWrite 370 support 67
- 71 — MD-Laser support 69
- 72 — Metacode support 69
- 75 — Continuous bell ringing 71
- 76 — Eliminate C0 05 header 71
- 77 — CR with each FF 71
- 78 — Laserpage support 72
- 79 — Continuous program mode 72
- 80 — Parallel port 1 timer 73
- 81 — Parallel port 2 timer 73
- 82 — Serial port 1 timer 73
- 83 — Serial port 2 timer 74
- PROGRAMMABLE FUNCTION 75
- Programming PFSs 76
- PFS Descriptions 78
- %61 — sc1 Replacement 84
- %62 — sc2 Replacement 84
- %63 — sc3 Replacement 84
- Job Boundary PFSs 85
- Job Boundary PFS Examples 86
- Print Job chart 91
- LU1 Session 91
- LU3 Session 92
- Translate Table Selection 94
- Functions 95
- Function Options 96
- Reading Translate Tables 97
- Modifying Translate Tables 98
- The Translate Tables 99
- Page 5-9TRANSLATE TABLES 101
- Page 5-11TRANSLATE TABLES 103
- Page 5-13TRANSLATE TABLES 105
- Page 5-15TRANSLATE TABLES 107
- Requirements 110
- APL Support 110
- Transparent (TRN) — 35h 117
- Vertical Tab (VT) — 0Bh 117
- SCS Command Summary 118
- Request Errors = 10h 119
- Request Reject = 08h 119
- XPAF Support 124
- Metacode Support 125
- Dip Switch Emulation 128
- Configuration Options 129
- PFS Downloading 138
- Accessing PFSs from the Host 141
- Translate Table Downloading 141
- B — Reserved (not used) 143
- C — Reserved (not used) 143
- Page 12-3APPENDIX 147
- Page 12-7APPENDIX 151
- Page 12-9APPENDIX 153
- Page 12-11APPENDIX 155
- Page 12-13APPENDIX 157
- Page 12-15APPENDIX 159
- Printer Test Report 161
- Plotter Test Report 162
- Host Diagnostic Report 163
- Page 12-21APPENDIX 165
- Page 12-23APPENDIX 167
- Page 12-25APPENDIX 169
- Pin-out Charts 172
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales